Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies HVAC Cleaning in Irving: What to Know First
We provide independent Abatement Technologies HVAC cleaning in Irving, TX, for homeowners who want the work documented, not just promised. Most Abatement Technologies systems we service in Irving, from the HEPA-AIRE product line to the Predator portable units, run between $280 and $520 for a full air handler and coil cleaning, with written pricing delivered before any panel comes off. We photograph every plenum, coil, and blower compartment before we touch it, and we leave you with those photos plus a written scope of what was found.
This page is for Irving homeowners running Abatement Technologies equipment, especially in the Las Colinas corridor and Valley Ranch, where we’ve found the hard water and summer humidity create specific buildup patterns on these systems. If you own a HEPA-AIRE SAH2, PAS2400, or Predator 750 and need the coils, blower, or full air handler cleaned, we can show you exactly what we’re dealing with before you decide. Call (682) 297-4068 for a free estimate with written pricing.
How Abatement Technologies Products Fail - and How We Fix Them
- HEPA-AIRE SAH2 Series: Blower wheel imbalance from fine particulate caking. The SAH2’s high-static blower pulls more than it filters when pre-filters are neglected. In Irving, we regularly find the blower wheel coated in a gray, cement-like layer of construction dust and pollen that throws the wheel off balance. The fix: remove the wheel, clean it on-site with a soft-bristle rotary tool, rebalance, and photograph the runout before reassembly. We only replace the wheel if the hub is scored.
- PAS2400 Portable: Evaporator coil fin corrosion from condensate pan overflow. The PAS2400’s shallow condensate pan in retrofit Irving installations, especially in older Valley Ranch townhomes, overflows when algae colonies block the drain. Water backs into the coil pack and starts fin corrosion. We pull the coil, treat the pan with an EPA-registered cleaner, clear the drain with nitrogen, and show you the fin condition under light before we quote any coil replacement.
- Predator 750: Heat exchanger soot scaling in heating-dominant setups. Irving homes running the Predator 750 as primary heat, particularly in the older Ranchview and Britain areas with original ductwork, develop soot scaling on the heat exchanger face from incomplete combustion. The camera shows it as a matte black crust. We media-blast the exchanger with crushed walnut shell, inspect for cracks under borescope, and document the before-and-after pressure differential.
- HEPA-AIRE H5000: Collapsed flex duct sections behind the air handler. The H5000’s higher static pressure, when paired with original Irving flex duct from the 2005-2015 build wave, collapses the inner liner at the first elbow. We’ve found this in Las Colinas condos where the unit is closet-mounted and the flex has no support. We replace the collapsed section with insulated hard pipe where space allows, or reinforced flex with proper saddles, and photograph the improvement in airflow at the register.
- Abatement Technologies UVGI systems: Lamp socket oxidation from humidity cycling. The UV-C lamps in Abatement Technologies air purifiers, common in Irving’s newer builds for allergen control, fail to strike when socket contacts oxidize from our 40-60% indoor humidity swings. The lamp looks fine; the socket doesn’t. We clean the contacts with electrical contact cleaner, test strike voltage, and only replace the lamp if output has degraded below 254 nanometers per our radiometer.
Our Abatement Technologies HVAC Cleaning Process
- 1
System identification and photo baseline. We record the model, serial, and installation date, then photograph every accessible surface: coil face, blower wheel, plenum walls, drain pan, and heat exchanger if applicable. The photo doesn’t lie - let’s look at it together before we talk about next steps.
- 2
Written scope and price under Haven Standard Clause 1. Tomas Reyes or a senior tech delivers a written price for the exact work shown in the photos. No per-vent add-ons, no “once we’re in there” surprises. You approve in writing or we leave with no charge for the diagnostic.
- 3
Component-specific cleaning with trade-recognized equipment. We match the tool to the component: Rotobrush contact cleaning for blower wheels, Nikro negative-pressure extraction for plenum debris, and Abatement Technologies-compatible coil treatment where fin corrosion is present. OEM parts are specified if warranty coverage is active; quality aftermarket is offered with full disclosure if not.
- 4
Functional test and pressure verification. We run the system through full heating and cooling cycles, measure static pressure across the coil, and verify condensate drain flow rate in gallons per minute. Abnormal readings are flagged in the written summary.
- 5
Photo record delivery and 365-Day Done Right Promise activation. You receive before-and-after photos of every cleaned component, the written scope, and the warranty document. If anything we cleaned fails due to our workmanship within 365 days, we return under Haven Standard Clause 5 and make it right.
BeforeAfterWhat Abatement Technologies HVAC Cleaning Costs in Irving
These are the whole-system ranges we quote in writing for Abatement Technologies equipment in the Irving market:
- Evaporator coil cleaning only: $280-$380
- Blower wheel and housing cleaning: $220-$320
- Full air handler cleaning (coil, blower, plenum, drain pan): $420-$520
- Heat exchanger cleaning with combustion analysis: $340-$460
- Condenser coil cleaning (outdoor unit): $180-$260
What moves the price: accessibility (attic vs. closet vs. rooftop), the degree of buildup documented in the initial photos, and whether fin corrosion or heat exchanger scaling requires additional treatment time. We also service Lennox, Trane, and Carrier systems with the same written-price protocol. Call (682) 297-4068 for an exact quote - estimates are free, and we deliver the number in writing before any work starts.
Why Irving Homeowners Call CleanRun Air Duct Cleaning Irving for Abatement Technologies Work
We’ve been running service calls through Irving since 2013, and the Abatement Technologies systems we encounter here, particularly in the Las Colinas corridor, have specific failure patterns tied to our local water and humidity. Our techs are background-checked and uniformed under Haven Standard Clause 3: Verified Crews, and they carry the equipment roster customers can verify: Rotobrush, Nikro, Abatement Technologies, Honeywell, Aprilaire, and Guardsman.
The 365-Day Done Right Promise is backed in writing on every job, not just stated in marketing copy. Every visit produces a Documented Photo Record of every duct run and HVAC component, included as a standard deliverable. And if you have a competitor’s written estimate for the same Abatement Technologies work, we offer a Free Second Opinion - our number next to theirs, no charge.
FAQs
No, professional cleaning by an independent service provider does not void your Abatement Technologies warranty, provided no components are altered or replaced with non-OEM parts without disclosure. We note warranty status before work begins and use OEM parts when coverage is active, quality aftermarket with full documentation if not. Call (682) 297-4068 if you need help verifying your warranty period.
We source OEM coils, blower wheels, and UV lamps through authorized Abatement Technologies distributors when warranty compliance requires it, and we show you the part packaging and serial before installation. For out-of-warranty systems, we offer quality aftermarket alternatives with manufacturer spec sheets you can review. Either way, it’s documented in your written scope.
Replace if the heat exchanger is cracked, the coil has multi-zone fin corrosion exceeding 40% surface area, or repair costs exceed 50% of replacement value. We make this recommendation based on what the camera shows, not age alone. Many HEPA-AIRE and Predator units in Irving have 15-20 year lifespans with proper cleaning. Call (682) 297-4068 and we’ll show you the evidence.
A typical single-system cleaning takes 3 to 5 hours from arrival to final test, depending on accessibility and the degree of buildup. We do not rush the photo documentation or the pressure verification. You’ll know the expected duration when you approve the written scope.
Yes, we clean Abatement Technologies portable units and fixed installations in light commercial applications throughout Irving, including medical offices and property management common areas. Commercial jobs receive the same written pricing, photo documentation, and 365-Day Done Right Promise, with scheduling arranged to minimize occupancy disruption. Call (682) 297-4068 to discuss your building’s specific equipment.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Irving at CleanRun Air Duct Cleaning Irving, serving Irving and nearby areas.