Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Nikro Air Quality & Sanitizing in Irving: What to Know First
We provide independent Nikro air quality and sanitizing service throughout Irving, from the Las Colinas corridor to the older ranch-style homes near Valley Ranch. Most Nikro mold treatment, bacteria sanitizing, or UV light installation jobs are completed in a single scheduled visit, with a written price delivered before any work starts. For whole-system Nikro sanitizing in Irving, homeowners typically see quotes between $380 and $720 depending on system size and contamination level.
This page is for Nikro owners in Irving who’ve noticed musty airflow, persistent odors, or allergy symptoms that correlate with HVAC runtime. If your Nikro air scrubber, UV system, or integrated purifier isn’t performing as documented, or if you’re considering adding sanitizing equipment to an existing Nikro setup, we can inspect, diagnose, and document what we find. Call (682) 297-4068 for a free estimate.
How Nikro Products Fail - and How We Fix Them
- Nikro PS2000 and PS3000 Series Air Scrubbers: UV-C lamp degradation without indicator failure. The lamps in these portable and inline units often drop to ineffective UV-C output (below 254 nanometers) while the status LED remains green. We measure actual irradiance with a UV meter rather than trust the lamp hour counter. Replacement with OEM-spec Nikro lamps or verified aftermarket equivalents restores kill rate on mold and bacteria.
- Nikro EC5000 Electronic Air Cleaners: Ionizing wire corrosion in Irving’s hard water vapor conditions. The Dallas-Fort Worth water supply runs high in dissolved minerals; when humid summer air moves through the EC5000, mineral deposits accelerate wire pitting. We find this most often in Irving homes with whole-house humidifiers tied to the same plenum. Our fix: clean the ionizing assembly with manufacturer-approved solution, test current draw across each wire, and replace only the degraded sections rather than the full cell.
- Nikro HEPA-AIRE Portable Units: Filter seal compression after repeated hot attic cycling. In Irving, attic temperatures regularly exceed 140°F in July and August. Nikro portable units stored or ducted through attic spaces develop gasket fatigue that bypasses HEPA filtration entirely. We pressure-test the seal with a smoke pencil, replace the gasket with high-temp silicone, and document the before-and-after leakage rate.
- Nikro APS2000 Allergen Reduction Systems: UV lamp ballast failure presenting as intermittent odor return. The ballast in early APS2000 units doesn’t fail outright; it sags voltage, which drops UV intensity just enough for microbial colonies to reestablish between cycles. We see this in Irving homes where the unit was installed in 2016-2018. Our diagnostic catches the voltage drop under load, and we replace with a ballast rated for the actual duty cycle, not the nominal spec.
- Nikro inline sanitizing injectors: Clogged nozzles from Texas dust and pollen loading. The fine-mist injectors used with Nikro’s sanitizing solution systems clog when pre-filtration is inadequate. Irving’s spring oak pollen and summer cottonwood particulate are particularly aggressive. We backflush the injector, verify droplet size with a laser diffraction check, and add or upgrade the pre-filter stage to prevent recurrence.
Our Nikro Air Quality & Sanitizing Process

- 1
Scheduled arrival with named technician. Haven Standard Clause 3: Verified Crews. You’ll receive the technician’s name and photo before arrival. Background-checked, uniformed, and equipped with Nikro-compatible diagnostic tools.
- 2
Written inspection with photo documentation. We access the plenum (the main distribution box where duct runs connect) and photograph every accessible surface before touching anything. The photo doesn’t lie - let’s look at it together before we talk about next steps.
- 3
Contamination identification and scope. We classify what we find: settled organic debris, active mold-like growth on duct liner, bacterial biofilm, or odor sources from external infiltration. Each requires different Nikro-compatible treatment.
- 4
Written price delivered before work starts. Haven Standard Clause 1. The scope, the equipment, the labor - all itemized. No per-vent pricing, no add-ons once the van is in your driveway.
- 5
Sanitizing execution with Nikro or cross-compatible equipment. Depending on scope: negative-pressure extraction (suction that contains debris during cleaning), UV-C lamp installation or replacement, HEPA filtration upgrade, or EPA-registered sanitizer application with dwell-time documentation.
- 6
Post-work photo record and written summary. Every duct run photographed after completion. Photos, scope summary, and 365-Day Done Right Promise delivered as standard job record.
Before
AfterWhat Nikro Air Quality & Sanitizing Costs in Irving
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Nikro UV-C lamp replacement (1-2 lamps) | $180 - $340 | Lamp spec (OEM vs. verified aftermarket), access difficulty |
| Nikro air scrubber / sanitizer installation | $580 - $1,200 | System tonnage, inline vs. bypass configuration, electrical run |
| Whole-system mold treatment with Nikro-compatible equipment | $680 - $1,450 | Contamination extent, duct accessibility, post-treatment verification testing |
| Nikro HEPA filter media replacement with seal service | $240 - $420 | Filter dimensions, gasket condition, frame corrosion |
These are whole-system ranges for Irving homes, typically 1,800-3,400 square feet. We don’t quote per-vent or teaser prices. The written estimate you receive is the price you pay. Call (682) 297-4068 for a free estimate - we’ll put our number next to any competitor’s written quote under our Free Second Opinion policy.
Why Irving Homeowners Call CleanRun Duct Cleaning Irving for Nikro Work

We’ve been running service calls in Irving since establishing our DFW operation, including repeat visits in the Las Colinas corridor where high-rise HVAC conversions and townhome systems create unusual Nikro configurations. Our 365-Day Done Right Promise applies to every job, backed in writing, not subject to manager discretion.
Tomas Reyes and our technicians are trained on Nikro’s product architecture as well as cross-compatible systems from Lennox, Trane, and Carrier. When a Nikro part is backordered or discontinued, we can source quality aftermarket equivalents or pivot to a compatible brand solution without leaving you in an open-ended “waiting on parts” status. Every technician operates under the H.A.V.E.N. Standard with published license verification. The photo record from every visit is yours to keep - useful for warranty claims, home sale disclosures, or your own reference.
FAQs
No, professional sanitizing using EPA-registered products and manufacturer-compatible UV lamps does not void Nikro’s warranty, provided the work doesn’t alter electrical or structural specifications. We document every product and procedure for warranty support. Call (682) 297-4068 if you need verification for your specific Nikro model.
We deliver before-and-after photos of every duct run and, for mold or bacteria treatments, can provide third-party lab verification at additional cost. The photo record is included standard; lab testing is optional and quoted in writing if requested.
Repair makes sense when the unit is under 8 years old and the failure is isolated to a replaceable component - UV lamp, ballast, or filter seal. Replacement is typically more economical when the core cell is corroded, the unit uses discontinued lamp geometry, or repair parts exceed 60% of replacement cost. We put both options in writing with 10-year operating cost projections.
Most residential Nikro UV lamp replacements or new inline installations are completed in 2-4 hours, assuming standard plenum access and no electrical panel upgrades needed. We schedule a four-hour window and update you if complications arise.
Yes. We are an independent Nikro service provider, not affiliated with or authorized by Nikro Manufacturing. This means we work on Nikro equipment using trade-standard parts and procedures, but we don’t represent the manufacturer for warranty claims. We document our work to support any warranty interaction you pursue directly with Nikro.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Irving at CleanRun Air Duct Cleaning Irving, serving Irving and nearby areas.




Before
After
Before
After